"Which brand do you use?" It's the first question at half our quotes. Fair question, wrong place to start. Most of the paint failures we get called to look at in Sydney have a perfectly good topcoat on them. What failed was the primer, the prep, or a product that was wrong for the wall.
For most Sydney exteriors, the paint that holds up in Sydney weather is a quality 100 per cent acrylic over the right primer. Acrylic stays flexible as the surface moves, holds colour under hard UV, and sheds water while letting a little vapour through. Two exceptions: older solid-walled homes, which need a breathable mineral or heritage-grade system, and metalwork, which needs its own primer before anything else.
A premium paint over poor prep fails before a mid-range paint over good prep. Pick the system for the surface and the exposure. Then put the effort into what goes under it.
Interior and exterior paint are built for different jobs
The difference is in the resin and the additives. Colour has nothing to do with it.
- Exterior paint has more flexible binders, so it moves with timber and render through hot days and cold nights without cracking
- Exterior paint carries UV stabilisers and mould inhibitors that interior paint doesn't need
- Interior paint is made to be scrubbable, low odour and low sheen without going chalky
- Interior paint has next to no UV or weather resistance, so it fails fast outside
- Exterior paint smells stronger and isn't designed for closed-up living spaces
Interior paint outside shows its mistake within a season or two. Exterior paint inside is unnecessary and unpleasant to live with. The grey area is a verandah, covered porch or enclosed sunroom, sheltered but still seeing outside air and temperature swings. Treat those as exterior.
What Sydney conditions demand from paint
- UV resistance: our sun fades colour fast. Deep reds and some blues go first, especially on north and west walls
- Flexibility: big daily temperature swings stretch the film. Brittle coatings crack at joints first
- Mould and mildew resistance: humid summers and shaded south walls make it worth paying for
- Salt tolerance and corrosion protection: near the coast or harbour, the metal under the paint matters as much as the paint
Coastal and harbourside homes
Salt changes everything. It settles on every surface, works into joints, and corrodes fixings, railings, brackets and window hardware from underneath. On a house in Mosman, Balmain or Hunters Hill, paint is the barrier keeping salt off the metal and out of the timber.
On those homes the sequence matters more than the brand. Rust gets taken back and treated. Bare metal gets a metal primer. Gaps get sealed so salty water can't sit behind the finish. The whole system has to work together, from bare surface up. Skip a step and the finish lifts in patches within a couple of years, starting at the fixings.
Older solid-walled homes need a different paint
A lot of Sydney's period housing has solid masonry walls with lime render and lime mortar. Those walls were built to take in a little moisture and dry back out through the surface. Seal them under a standard acrylic and the moisture can't escape. It travels through the wall until it finds a weak point, brings salts with it, and you get blown render and peeling paint that keeps coming back however well it's prepared.
On those homes we use a breathable mineral or heritage-grade paint, with lime renders and mortars underneath. It's a large part of what goes into painting period homes properly, and we explain the mechanism in why old homes need to breathe.
Matching the paint to the surface
- Weatherboard and timber cladding: flexible acrylic over a suitable primer, with bare timber spot-primed first
- Modern rendered masonry: acrylic render coating, once cracks and drummy patches are repaired
- Old lime-rendered solid walls: breathable mineral or heritage-grade system. No sealing acrylic
- Timber windows, doors and trim: a harder-wearing enamel for anything that gets handled, opened and shut
- Cast iron, railings and metal: rust treatment, metal primer, then finish coats
- Fibro and cement sheet: sealed and primed before coating
- Face brick: leave it unpainted. Painting brick is close to impossible to reverse
Sheen level is a practical decision
Higher sheen is tougher and easier to wash. It also shows every bump and patch in the surface. Lower sheen hides flaws and marks more easily.
- Exterior walls: low sheen. Forgiving on older surfaces and doesn't spotlight patched areas
- Exterior trim, windows and doors: satin or semi-gloss, because it handles weather and fingers better
- Interior walls: matt or low sheen in living areas, washable low sheen in hallways and kids' rooms
- Interior trim and doors: satin or semi-gloss so it wipes down
- Kitchens and bathrooms: a moisture-resistant finish with some sheen
Don't save money on the primer
Primer bonds the system to the surface. Bare timber, bare metal, fresh render, patched areas and big colour changes all need primer, and they don't all need the same primer. Timber tannins bleed through without a stain-blocking primer. Rust comes straight back without a metal primer. Fresh render is alkaline and attacks a finish coat put straight onto it. Give new cement render at least four weeks to cure before it's painted.
Most early paint failures we look at are primer failures. The topcoat just gets the blame.
Colour and heat
Dark colours absorb more heat. More heat means more movement in the surface underneath and faster fading under our sun. You can still use them, and plenty of period palettes call for deep tones. Just know a dark exterior will need attention sooner than a pale one, especially on a west wall. Our guide to choosing period-correct colours covers the heritage side.
We specify the paint system for each house, and we'll tell you exactly why we picked it. See our exterior painting and painting work across Sydney, or book a free on-site quote and ask us the brand question. We'll answer it, then tell you about the primer.