Stand across the street from a Paddington or Glebe terrace and look up at the balcony. The cast-iron lacework is still there, but the pattern has gone soft. The ferns, lyres and scrolls a foundry poured in the 1880s now look like someone iced them. That's forty or fifty coats of paint, and restoring cast-iron lacework starts with getting most of them off.
The question we get first: "Can't you just give it another coat?" We can. It'll look worse, and the rust under the old layers keeps going.
What's actually on your lacework
Most Sydney lace went up between the 1860s and the 1890s. It's grey cast iron. Hard, heavy and brittle. That last one matters more than anything else on this page. Cast iron doesn't bend. Hit it hard, lever it, or heat one side fast, and it cracks.
Under the paint are layers going back to the day it was installed. Anything painted before about 1970 has lead in it, so the bottom coats on your lace almost certainly do. On plenty of terraces the bottom layers are old oil-based lead paint and the top few are acrylic someone rolled on in the nineties. Bad pairing. The acrylic flexes, the old oil paint underneath is brittle, and the whole stack lets go in flakes the size of a fingernail.
Where cast-iron lace fails first
- The bottom rail and the base of each panel, where rain sits after a storm
- Fixing points, where the lace bolts to verandah posts or is leaded into sockets cut in sandstone or brick
- The seams where two castings meet and the paint has cracked along the joint
- Anywhere a dripping gutter or a split downpipe lands on it
Watch the fixings. Rusting iron swells to several times its original volume. When that happens inside a socket in a sandstone sill or a brick pier, it splits the stone. The trade calls it rust jacking. We see verandah edges with a cracked sandstone step, and the cause is a bolt nobody has looked at in a hundred years.
How we strip cast-iron lacework
There are four ways to get old paint off iron lace. Two of them suit most jobs.
- Chemical stripper: a paste spread on thick, left for hours under plastic, then scraped and brushed out of the pattern. Slow and controlled, and it doesn't stress the casting. This is our main method for lace that stays in place
- Hand tools: picks, small scrapers, brass and steel brushes for the deep recesses. There's no fast way through a cast fern
- Heat: a heat gun on a low setting softens paint, but cast iron pulls heat away fast and uneven heating cracks thin sections. Lead paint must never be burnt off. We keep heat to a minimum on lace
- Abrasive blasting: fast and thorough, done off site at a blasting yard. Fine for heavy columns and brackets. Risky on thin or already-cracked panels
Whatever the method, lead stays contained. Drop sheets under the work, debris bagged and removed, no dry sanding of old lead layers into your front garden or the neighbour's. Kids and pets stay clear until it's cleaned up.
Take it down or work in place?
Most lace gets done where it hangs. Taking it down risks breaking it, and old lace leaded into stone sockets doesn't want to come out.
Panels come down when they're badly cracked, when the fixings have rusted through, or when blasting is the only way to clear decades of paint from the pattern. They go off to be stripped and repaired, and while they're away the sockets get cleaned out and the stone around them repaired so the rust jacking doesn't start again.
Broken and missing pieces
A cracked casting can be pinned, brazed or plated from the back. A missing panel can be recast: a foundry takes a sound panel from your house, or a matching one from the street, makes a sand mould from it and pours a new one. Some owners choose cast aluminium for replacements because it's lighter and won't rust. I'd still put iron back on a terrace that's been iron since the 1880s. If the house is heritage listed, check with council before replacing anything.
Rust treatment and the paint system
Once the iron is bare, the clock starts. On a humid Sydney morning bare cast iron shows flash rust within hours. Primer goes on the same day it's cleaned. Always.
- Remaining rust taken back with wire brushes until you're down to sound grey metal
- A solvent wipe to lift stripper residue, grease and dust out of the recesses
- An anti-corrosive metal primer, brushed into every recess. A roller or spray misses the back faces and the undersides, which is exactly where water sits
- An extra primer coat on edges, the bottom rail and the fixings, where failure starts
- Two finish coats of gloss or semi-gloss enamel. Gloss sheds water and dirt better than anything flat
Near the harbour, in Balmain, Mosman or Hunters Hill, salt changes the maths. Salt air gets into the smallest crack in the film and starts rust from underneath. On those homes the total film goes on thicker and the bottom rail gets a third finish coat. A hose-down twice a year keeps salt off it between repaints.
What colour should the lace be?
Victorian lace was rarely white. It was painted to look like bronze or some other expensive metal: deep bronze green, chocolate brown, Indian red, near-black. Set against a lighter stone-coloured wall, dark lace reads as a pattern from across the street. White lace on a cream wall disappears.
Some boom-era terraces did pick out the lace in two colours, with the fine detail highlighted. Do the paint scrape first and see what was there. There's more on period palettes in our guide to choosing heritage paint colours.
How long it takes
A single-storey verandah frieze, stripped and repainted in place, runs 3 to 5 days. A two-storey terrace with a full balcony balustrade, brackets, frieze and columns is closer to 2 to 3 weeks, and most of that is stripping. It's slow because the pattern is slow. You can't roll a fern.
Worth it, though. Get the lace crisp again and the whole frontage looks like someone cares about it.
Lacework is part of our facade restoration work, and it's done alongside heritage painting on the rest of the front by the same team. If your balcony looks iced, book a free on-site quote and we'll tell you whether it needs a full strip or a careful touch-up.