The phone call goes like this: "We painted the hallway eighteen months ago and it's bubbling again at the bottom." It's a Leichhardt or Annandale terrace. The paint is blistering in a band about 600mm high, and there's white fluff growing out of the plaster. That's rising damp, or something that looks a lot like it.
Rising damp in old Sydney homes is common and it's fixable. It's also the problem most likely to get painted over three or four times by people who should know better.
What rising damp is
Ground moisture climbs through masonry the same way coffee climbs up a sugar cube. Brick, sandstone and lime mortar are full of fine connected pores. Without a barrier, water rises until evaporation off the wall face balances what's coming up from below. In a solid brick wall that balance point sits somewhere between 600mm and 1.5 metres.
The water does some damage. The salt it carries does most of it.
The salts doing the damage
Groundwater carries dissolved salts. When the water evaporates at the wall surface, the salts stay behind and build up, year after year. Three kinds matter.
- Sulphates crystallise and expand as they dry. They push plaster and render off the wall and turn soft brick faces to powder. That white fluffy bloom is mostly sulphate
- Chlorides are hygroscopic, which means they pull moisture out of the air. A wall loaded with chlorides goes damp on a muggy February day even when the ground is dry
- Nitrates come from old soil, drains, stables and anything organic. Inner-city ground that's been lived on for 150 years has plenty. Also hygroscopic
This is why a wall can stay damp after you've stopped the water. The salt is still in it, drawing moisture from the air. It also fools moisture meters. Salt conducts electricity, so a salty wall reads wet on a cheap meter when it's dry. Anyone diagnosing rising damp off a meter reading alone is guessing.
Damp-proof courses, and why yours might not be working
Most Sydney houses from the 1880s on were built with a damp-proof course: a layer of slate, bitumen felt or tarred material laid in a mortar joint two or three courses above ground. Some earlier houses had none. Slate cracks when the house settles. Bitumen goes brittle after a century.
The commonest cause we find is a bridged DPC. The barrier is still there, and something is letting water walk around it.
- A garden bed built up against the wall above DPC height
- A concrete path or courtyard poured higher than the original ground level
- Cement render taken down the face of the wall over the DPC to the ground, giving water a path straight past it
- Subfloor vents blocked by paving, a deck or a well-meaning owner trying to stop draughts
- A leaking downpipe, a cracked stormwater pipe, or a tap that drips into the base of the wall
That last group is a plumbing problem wearing a damp costume. Fix the pipe and half of it goes away on its own.
How to spot rising damp
- A tide mark low on the wall, roughly level, within 1.5 metres of the floor
- Paint blistering, flaking or bubbling in a band just above the skirting
- White salt bloom on the surface, or plaster that's gone soft and crumbles under your thumb
- Skirting boards rotting from the back or pulling away from the wall
- A musty smell in rooms along that wall, worse after a wet week
A damp patch high up, near the ceiling or under a window, is coming from somewhere else: a box gutter, a parapet, a failed sill. Different problem, different fix. Our post on the signs a heritage home needs remedial work covers those.
Why painting over rising damp fails
"Can't you just paint over it?" Yes. It'd look good for a season.
Then the salts crystallise behind the new film, the paint lifts, and you've paid for it twice. Use a damp-sealing paint and it gets worse. The moisture can't come out where it used to, so it climbs higher and comes out above the sealed patch. Patching with cement render does the same thing. The tide mark moves up 300mm and the wall behind the cement stays wet for good.
Fixing rising damp properly
Order matters. Skip a step and the repair fails.
- Find the source. Start outside: ground levels, paths, garden beds, downpipes, subfloor vents
- Remove the bridging. Lower the bed, cut back the path, strip cement render off the base of the wall
- If the DPC has genuinely failed, put a new one in. A chemical DPC is a silane cream injected into holes drilled along a mortar course. A physical DPC means cutting out a mortar course in short sections and slotting in a new membrane
- Strip the salt-loaded plaster or render to about 300mm above the highest sign of damage
- Let the wall dry. The old rule of thumb is a month for every 25mm of wall thickness, so a 230mm solid brick wall wants most of a year to dry right through
- Draw out salts with a poultice, or a sacrificial lime render that soaks up salt and gets replaced
- Replaster in lime, and finish with a breathable paint
You don't have to wait the full year to replaster. You do have to use materials that let the wall keep drying after you've finished. That's the step most fixes skip, and we explain why in our post on why old homes need to breathe.
What it costs to leave it
Rising damp doesn't hold still. Every wet and dry cycle moves more salt into the wall. Brick faces fret, mortar turns back to sand, skirtings rot, and floor joists bearing on that wall go soft at the ends. We've seen bottom courses you could dig out with a teaspoon.
Caught early, it's a few metres of plaster and a downpipe. Left for twenty years, it's rebuilding the base of the wall.
We treat damp and salt at the source, then replaster and repaint. That's our remedial repairs and waterproofing and sealing work, done by the same team that paints the wall at the end. Book a free on-site quote and we'll find where your water's coming from before anyone opens a tin.